Genie z60/34 manual

Page Jib Boom Components Crushing hazard. The platform Component damage hazard. Page Jib Boom Lift Cylinder 4 Remove both of the jib boom leveling links from unbalanced and fall when it is the machine. Page 86 Remove the jib boom lift cylinder from the machine. The jib boom lift cylinder could become unbalanced and fall when removed from the machine if not properly attached to the overhead crane.

Platform rotate circuit Orifice, 0. Platform rotate circuit Part No. Page Primary Boom Components Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray.

Page 90 16 Remove the cable track guide fasteners from the platform end of the primary boom. Page Primary Boom A 7 link repair section of cable procedure requires specific repair track is available through the skills, lifting equipment and a Genie Industries Service Parts suitable workshop.

Attempting this Department. Page 92 12 Attach a similar lifting device to the primary boom lift cylinder. Page 93 Pay careful attention to the platform end of the primary boom. Page 96 Bodily injury hazard. Page Platform Leveling Master Cylinder 1 Remove the pin retaining fasteners from the the oil pressure to dissipate master cylinder rod-end pivot pin. Use a soft gradually. Do not allow oil to metal drift to remove the pin. Page 98 7 Lower the master cylinder down and out of the upper pivot and remove it from the machine.

The master cylinder could become unbalanced and fall when removed from the machine if not properly attached to the overhead crane.

Page Secondary Boom Components Dealer service is required. Follow the disassembly steps to the point required to complete the repair. Then re-assemble the secondary boom by following the disassembly steps in reverse order. Page Crushing hazard. Failure to secure secure the upper pivot from moving. Page Cap the fittings on the Crushing hazard. The secondary cylinder. Page Do not allow oil to squirt or spray. Page Part No.

The secondary boom lift cylinder could become unbalanced and fall when removed from the machine if not properly supported by the overhead crane. Page Rpm Adjustment Deutz models inch flex plate with raised spline 9. Page 5 minutes. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury.

Remove all rings, watches and other jewelry. Page Hydraulic Pumps Rexroth and then torqued to specification service center. Call Genie Industries Service during installation. Department to locate your local authorized service Refer to Section 2, Hydraulic Hose center.

Pressure in from drive pump Page Function Manifold Components - View Jib select Flow control Function pressure control Please turn the page. Page Solenoid valve, 2 position 3 way..

Boom retract Testing Check valve Jib boom select Do not adjust valve pressure. Page Install the relief valve cap. Tip-over hazard. Do not adjust the relief valve higher than specified.

To tank Check valve To tank Part No. Page Directional Valve Manifold Components The directional valve manifold is mounted inside the drive chassis at the non-steer end. Index Description Function Torque Cap Page 6 the machine tipping over. Testing Shuttle valve, 3 position 3 way.. Change pressure, hot oil shuttle.. Drive motor anti-cavitation Controls flow to steer end drive motors in forward and reverse Properly functioning coil diodes protect the electrical circuit A properly functioning coil provides an by suppressing voltage spikes.

Genie part number 5 Momentarily connect the positive lead from the multimeter to the positive terminal on the 9V DC The battery should read 9V DC or battery. Page Axle Components Always use a new cotter pin when installing a castle nut. Torque the wheel lug nuts to specification. The oscillate at the steer end. Remove the cover. Be sure that all necessary tools and test equipment are available and ready for use.

Observe and Obey: Read each appropiate fault code thoroughly. Page Just calibrated of alarm. Continued on next page Part No. Page Self-clearing. Just calibrated is zero. Page Initiate 1-second beep Self-clearing. Just calibrated of alarm.

Page Check Engine Light. Use the Fault Code Chart on the following pages to aid in identifying the fault. OR replace the ECM. Page OR replace ignition coil 1. OR replace ignition coil 1. Page 2 shorted OR connections to ignition coil 2 ignition coil 2 is faulty. OR replace ignition coil 2. Industries Service Department. If this fault appears on your Page Spark Rev Limit sticking open OR there are air repair any air leaks between leaks between the throttle body the throttle body and cylinder and cylinder head.

Page Do not allow oil to squirt Read, understand and obey the safety rules or spray. General Repair Process Be sure that all necessary tools and test equipment are available and ready for use.

BR-2 Part No. Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. With this Genie electric boom lift, operators can easily work close to buildings or around obstacles and access over Electric scissor lifts of today are typically powered by lead-acid batteries, which are comprised of a number of lead plates in a bath of acid.

Booms lifts are common equipment on a variety of different jobsites. But before you can start working with a boom, you have to get it to the jobsite. To do this safely and efficiently, there are some important considerations. In addition to the ability to reach up, over and out, one of the features that make trailer-mounted booms a popular option for work at height is their ease of transport and mobility.

Dual Parallelogram Linkage. Drive Systems - Part 2. Active Oscillating Axles.